Hochfrequenz Coronagenerator zur Vorbehandlung nicht leitender MonTEC ist ein zusätzliches Überwachungssystem zu Tantecs Plasma und Corona. disadvantage – low surface energy, resulting in poor surface adhesion for water- based adhesives and inks. Corona treatment systems by Tantec significantly. EPA4 * Korea Mach & Materials Inst Apparatus for plasma generation, method for manufacturing rotating electrodes for plasma.
|Published (Last):||13 May 2006|
|PDF File Size:||12.16 Mb|
|ePub File Size:||1.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
Tantec SpotTEC is used for treatment of profiles, cables and injection moulded parts.
The SpotTEC is easily adopted into any production line and offers the user a high level of flexibility in use. The SpotTEC is based on the principle of high-voltage discharge in atmospheric air blown towards a substrate surface.
The purpose of surface treatment of polymer based materials is to increase surface wettability through electrical discharge. The low surface energy of polymer based substrates often leads to poor adhesion of inks, glues and coatings. To obtain optimum adhesion, it is necessary to increase the surface energy of the substrate to just above that of the material to be applied.
Vetaphone – The leading supplier of Corona systems
Surface treatment with corona results in improved surface adhesion properties. PP board is made of blended PP co-polymer and has one major disadvantage – low surface energy, resulting in poor surface adhesion for water-based adhesives and inks.
Corona treatment systems by Tantec significantly increase surface energy and improve adhesion.
The purpose of surface treatment of polymer-based materials is to increase surface wettability through electrical discharge. The low surface energy of polymer-based substrates often leads to poor adhesion of inks, glues and coatings. Surface treatment with Corona results in improved surface adhesion properties.
Tantec RotoTEC-X is used for in-line treatment of injection moulded parts prior to coating, printing, gluing, painting etc. The RotoTEC-X ensures a very uniform treatment process and offers the user full process control of all parameters. The PipeTEC is designed for treatment of the inside surface of jacket pipes for optimised adhesion of PUR foam which is needed coroma insulation of the pipe core.
The PipeTEC must be fully integrated into an extrusion line and ensures a very high level of surface treatment of the entire inside surface.
Normally the SyrinTEC is built into the coroba line and positioned as the final process before the barrels enter into the printing machine.
Using the SyrinTEC enables treatment of the entire outside surface without any inside treatment, which would increase friction on the inside barrel and cause the plunger to drag when used. Single-use needles make up a significant percentage of the disposable medical device market.
THE CORONA PROCESS
Billions are produced annually, for use in a wide variety of devices. The OSHA-driven Needlestick Safety and Prevention Act requires needle manufacturers to provide safer alternatives to existing needle designs, resulting in hundreds of new designs annually. In an vornehandlung to comply with this act while remaining competitive in the marketplace, manufacturers are exploring the uses of adhesives to facilitate needle assembly. The versatility of this unit allows for use in vorbehandlunv integrated robotic cells, as a standalone unit, or most any production line.
Corona Systeme & Corona Anlagen | Individuelle lösungen
Two common applications for pre-treatment of automotive EPDM- profiles with plasma are prior to flocking and slip-coating. In the flocking process, treatment is necessary to achieve a strong bond between the rubber and the adhesive used to attach the flock. For slip-coating it is necessary to treat prior to the spray process to achieve good wettability and optimum adhesion properties of the coating.
The VacuLAB offers the ability to handle small scale testing and of- fers the user full control of all parameters.
The VacuTEC is available with both single and multiple tray configuration. The VacuTEC offers very fast treatment times and optimum adhesion properties for down- stream coating, gluing, painting and printing applications. The VacuTEC offers very fast treatment times and optimum adhesion properties for downstream coating, gluing, painting and printing applications.
Tantec RotoVAC plasma treater is designed for plasma treatment of vorbehandlunng injection moulded plastic parts, without the need to place them in a jig or use complicated handling systems. With the RotoVAC drum design, simply fill the drum and place it in the vacuum chamber.
The rotation will ensure that all parts are treated. The vorbehhandlung is ideal for in-line production, where no operators are needed. The VacuLINE system offers very fast treatment time and optimum adhesion properties for downstream coating, gluing, painting and printing applications.