CANON IR3300 ERROR CODES LIST PDF

Canon Ir Error Code List. Code Description. E Communication error ( with pedestal). E Communication error (with ASSIST). Free downloads Error Codes Canon iRPage 1 of 5 Error Codes Canon iR Download here the full version of service manual iR Code List. Thank you for purchasing the Canon iR/iR/iR Series Machine. This Manual describes the use of the List of Error Codes Without Messages.

Author: Mazura Shaktilmaran
Country: Colombia
Language: English (Spanish)
Genre: History
Published (Last): 7 November 2013
Pages: 16
PDF File Size: 19.93 Mb
ePub File Size: 19.35 Mb
ISBN: 963-2-22087-232-4
Downloads: 29004
Price: Free* [*Free Regsitration Required]
Uploader: Daigul

E While the ADF is in standby, the communication with its host machine is disrupted for 5 sec or more; or, while the ADF is in operation, the communication with its host machine is disrupted for 0. E At the start of the motor CW operation, the stack handling motor M2 may be driven for a specific number of rotations; however, the stack delivery lever home position sensor S8 does not go ON. Main cause The connection of the IC socket is faulty.

Cause The front alignment motor M3 is faulty.

Canon Ir 3300 Error Code List

Main power supply PCB: Main cause The wiring it3300 faulty short circuit, open circuit. Execute the following in service mode: Film rotation detection signal: The thermistor has a short circuit.

Connector Is the connector of the fixing assembly connected? Main cause The HDD is cann. Malfunction, PCBs Turn off and then on the main power switch. The fixing heater has an open circuit. Replace the main power supply PCB. The wiring is faulty. The output for primary charging, developing, or transfer has deviated from a specific level of voltage.

  COLLIN MOSHMAN HEADS-UP NO-LIMIT HOLDEM PDF

Main cause The waste toner case is full.

Canon IR 3300 Error Code List

When the fixing motor is rotating, is the film rotation detection signal sent lisr the fixing film sensor to the concoctor J of the DC controller PCB? Main cause The inverter PCB is faulty.

The delivery belt home position motor PI7 is faulty. Main cause The scanner home position sensor PS is faulty.

Error Code Ir e and e

E At the start of the motor CCW operation, the stack handling motor M2 may be driven for a specific number of rotations; however, the stack delivery lever home position sensor S8 does not go ON.

The rear aligning plate is subjected to an excess load. E A fault is detected in the image memory.

Connector Is the printer board accessory connected correctly? The detail codes of the fans in question are as follows: Making Corrections Downloading system software Check the types of the BootROM and the system software, and download system software cqnon the correct type.

The main controller PCB has a fault. Foreign matter Is there foreign matter that prevents the rotation of the fan?

Main cause The feed motor M1 is faulty. Main cause The contact has poor connection. Check the interval between pin 1 and pin 2 and between pin 3 and pin 4 of the connectors 4-pin of the thermistor for electrical continuity. E A fault is detected in the battery for the image memory. Connector Is the xodes of the fixing motor connected?

  CISCO SLM2024 MANUAL PDF

Archives December August July Main cause The fixing motor M19 is faulty. The aligning plate home position sensor front; PI4 is faulty. Main cause Caonn folding roller home position sensor PI12 is faulty. Connector Is the connector of the main motor connected? Categories Blog Manuals Service Specification. The sensor is faulty and cannot detect home position.

The reader controller PCB is faulty.

Canon Ir Error Code List – Copy Care Enterprise

Is it 0 W short circuit? The main controller PCB is faulty Action a. The communication line has an open circuit. E The puncher not leave home position when the lits shift motor is driven for 1 sec.

Caution To clear the error, execute the following in service mode: The stapling home position sensor S16 dos not go ON with 0. The image data has a fault. The puncher shift motor M2P is faulty.

Action See the description for E